How to Fix a Torch Lighter That Won't Light
If your torch lighter is not working, check four things in order: the tank, the burner, the spark wire and the flame setting. At Humidorist, we put the troubleshooting steps from Xikar, Colibri, Neptune Cigar and Online Cigars in one order so you can work down it.
While our guide on how to refill a butane torch lighter covers routine filling and addresses common fill issues, stubborn ignition failures require mechanical checks. These diagnostic steps apply to butane torch lighters generally, whether you own a single-jet pocket model or a multi-jet tabletop torch.
If a hiss carries on after refilling, stop using the lighter. Online Cigars says that means butane is escaping from a worn valve or gasket, and escaping butane can ignite.
Fix It in This Order
Work through these four diagnostic checks in sequence.
- Purge trapped air and refill the fuel reservoir. Neptune Cigar notes that improper bleeding causes most lighter malfunctions. To purge the tank, hold the lighter upright away from your face and ears. Use a small screwdriver or a blunt tool to depress the filler valve at the base until all escaping gas and hissing stop completely. Do this away from flames and sparks. Shake the lighter and repeat the depression to confirm the chamber is empty. As described by Keith Dooley at Hunker based on troubleshooting guidance from Colibri, turn the flame adjustment wheel to the minimum setting before bleeding. Once purged, invert the lighter so the refill valve points upward, press the butane canister nozzle firmly into the valve opening, and allow the tank to fill. Neptune Cigar says to press for 4 to 5 seconds, then warm the lighter in your hand for at least 30 seconds and wait another 2 minutes before igniting, so the excess butane dissipates and the gas reaches room temperature.
- Clear the burner nozzles using compressed air. Xikar says accumulated debris might clog the burner when a lighter fails to ignite consistently or burns weak. The Xikar troubleshooting page recommends using low-pressure air, such as an electronic duster, to dislodge foreign particles from the burner housing. Aim the nozzle into the burner cups and give two to three bursts of one to two seconds. Hunker and Online Cigars give the same air-blast step, and Hunker says to hold the nozzle at least one to two inches from the coils. James Peasley at Online Cigars also says to blow dust and carbon out of the jets and ignition area with compressed air.
- Inspect the position of the spark wire. The Xikar troubleshooting page explains that if the lighter clicks, fuel flows, and a spark is visible yet no flame appears, the direction of the spark wire may be the problem. Xikar publishes a video tutorial on adjusting the spark direction. Xikar's steps are mainly video, so check the manual for your lighter's model before you adjust anything.
- Calibrate the flame adjustment setting. Keith Dooley at Hunker explains that adjusting the flame wheel toward the plus symbol increases gas flow when output is weak, while turning toward the minus symbol lowers an erratic flame. James Peasley at Online Cigars notes that adjustments should always be made in small increments because sudden turns can cause sputtering or over-fueling. If external adjustments fail, Xikar's troubleshooting page explains an internal adjustment for lighters whose flame stays permanently too high or too low. Using a small screwdriver, remove the retaining screw from the adjustment wheel on the side or top of the housing and set it aside safely. Lift off the wheel, use small pliers to adjust the regulator up or down a quarter of a turn, checking the markings on the wheel for the direction, test the ignition, and reinstall the wheel and screw. Avoid over-tightening the retaining screw during reassembly, because Xikar says over-tightening can damage the valve or fuel wheel.
Symptom and Fix Table
Use this reference table to match the behavior of your lighter to the most probable malfunction, the recommended corrective action, and the supporting industry source.
| Symptom | Most Likely Cause | What to Do | Source |
|---|---|---|---|
| No flame and no gas sound | Trapped air or an empty tank (Neptune Cigar says most problems are incorrect bleeding) | Bleed the valve completely, refill upside down with premium butane, warm it in your hand for 30 seconds, then wait 2 minutes | Neptune Cigar, Hunker / Colibri |
| Click and spark visible, but no flame | The direction of the spark wire | Follow Xikar's video on adjusting the spark direction | Xikar |
| Weak, flickering, or yellow flame | Debris in the burner | Blow low-pressure air into the burner in 1 to 2 second bursts | Xikar, Hunker / Colibri |
| Flame too high or sputtering wildly | Flame setting out of range | Adjust in small increments, toward minus if too high and plus if too low. Xikar describes an internal quarter-turn adjustment | Xikar, Online Cigars, Hunker / Colibri |
| Continuous hiss after releasing ignition | Butane escaping from a worn valve or gasket (Online Cigars) | Stop using the lighter and contact the seller or maker about a return or warranty | Online Cigars, Neptune Cigar, Xikar |
Why Torch Lighters Stop Working
Neptune Cigar says most lighter problems come from incorrect bleeding, and that air can go into the tank when you refill, which is why it says to fill with the lighter upside down.
Fuel matters too. James Peasley at Online Cigars says butane refined at least five times is the cheapest repair you can make. Neptune Cigar recommends using premium triple-refined fuels with metal fill tips from brands such as Colibri, Nibo, or Prometheus, and says non-premium butane may cause inconsistent ignition. Neptune Cigar says that if you used non-premium butane, bleed the tank and refill.
Xikar says debris can clog the burner, and its fix is short bursts of low-pressure air.
Online Cigars says a cold valve can temporarily affect gas flow, and that letting the lighter sit at room temperature for a few minutes helps. Neptune Cigar says higher altitude calls for less butane flow (turn the adjustment clockwise) and lower altitude calls for more.
When to Stop Using the Lighter
A continuous hiss after refilling is the one symptom that means stop.
James Peasley at Online Cigars warns that while a momentary hiss during the refilling process is normal, a hiss that continues afterward indicates fuel escaping through a worn valve or a compromised internal gasket. Online Cigars identifies an ongoing leak as the one fault you should never attempt to repair at home. Neptune Cigar provides similar guidance: if a lighter leaks butane or its ignition will not spark, it says to contact Neptune Cigar to return it.
For quality lighters that fail to ignite after you have cleared the jets, purged the tank, and adjusted the flame, the manufacturer's warranty is the next step. Brands like Xikar provide a Limited Lifetime Warranty on their lighters. The Xikar FAQ notes that product registration is unnecessary to receive service. Butane, humidifiers and flints are not covered by that warranty. You can submit a claim directly through the Xikar Limited Lifetime Warranty claim page.
Keeping a Torch Lighter Reliable
The Xikar FAQ states that a can of butane can last up to five years in a controlled temperature environment, and says not to keep butane or a lighter in extreme heat or cold or in direct sunlight, which could lead to performance issues or damage. When refilling, avoid shaking the butane can beforehand, as James Peasley at Online Cigars notes that shaking introduces air bubbles into the liquid fuel stream.
Give your torch time to recover between lighting sessions. James Peasley at Online Cigars explains that rapid, repeated ignitions can overheat the lighter, so rest it between uses. Our guide on how to light a cigar covers the lighting technique.
When a lighter wears out beyond the reach of warranty service, our roundup of the best cigar lighters covers replacement picks.
Our Takeaway
Work the checks in the order shown: bleed out trapped air, refill the reservoir with the lighter inverted, blow out the burner cups with low-pressure air, check the spark wire alignment, and reset the flame adjustment wheel. If butane continues to hiss after refilling, stop using the lighter immediately because Online Cigars calls a leak the one fault not worth repairing yourself. When a lighter still refuses to light after complete purging, nozzle cleaning, and spark alignment, use the manufacturer's warranty route or replace the unit.
This guide is not for a lighter with a hiss that carries on after refilling: stop using it. It is also not for liquid-wick lighters, which work differently, so see our guide on Zippo for cigars. If your lighter manufacturer provides an official user manual specifying an alternative bleeding, refilling, or regulator calibration procedure, follow the manufacturer's specific instructions.
FAQ
How do you fix a torch lighter that will not light?
Fix a non-lighting torch lighter by bleeding the tank completely, refilling it with clean butane, and clearing the burner nozzles. Depress the base filler valve with a small screwdriver until all trapped air and residual gas escape, turn the flame adjuster to minimum, and fill the tank with the lighter held upside down. Neptune Cigar says to warm the lighter in your hand for 30 seconds, then wait another 2 minutes. If the lighter still fails to strike, blow two to three short bursts of low-pressure air into the burner to dislodge dust.
What causes a torch lighter to stop working?
Neptune Cigar says most lighter problems come from incorrect bleeding, and that non-premium butane may cause inconsistent ignition. Xikar says accumulated debris might clog the burner. Online Cigars says a cold valve can affect gas flow and that rapid, repeated ignitions can overheat the lighter.
How do you burp a torch lighter?
Burp a torch lighter by holding the lighter upright and depressing the bottom refill valve with a small screwdriver or a blunt tool. Keep the valve depressed until the hissing sound stops and no further gas or air escapes from the chamber. Shake the lighter gently and press the valve a second time to ensure all trapped air pockets are evacuated. Neptune Cigar advises performing this bleeding process whenever fuel drops low, before adding fresh butane, and keeping the lighter away from your ear while discharging.
How do you get a lighter to spark again?
Start with the burner. Hunker's Colibri steps say to blow carbon and dirt off the ignition coils inside the burner with compressed air held at least 1 to 2 inches away. If there is a click, fuel flow and a spark but no flame, Xikar says the direction of the spark wire may be the problem and publishes a video on adjusting it.
Can you fix a lighter that will not spark?
Sometimes. If the lighter clicks, fuel flows and there is a spark but no flame, Xikar says the direction of the spark wire may be the problem. If the ignition does not spark at all, Neptune Cigar says to contact it to return the lighter, and a Xikar lighter can go through Xikar's warranty claim.
How do you fix the igniter on a torch lighter?
Xikar's guidance covers the spark wire direction when the lighter clicks and sparks but does not light, and Hunker's Colibri steps cover cleaning the ignition coils with compressed air. If the ignition still does not spark, Neptune Cigar says to contact it for a return, and Xikar lighters go through the Xikar warranty claim.
Bleed the tank and refill it upside down with the steps in how to refill a butane torch lighter, then work down the checks above.